1
Add-Ons / Re: TheTurtorns Mitsubishi Evolution VIII Modified (Vehicle restoration)
« on: February 22, 2017, 10:15:37 PM »You have other vehicles??My old thread had a list, I think there's only 1 missing which I posted on page 24
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Add-Ons / Re: TheTurtorns Mitsubishi Evolution VIII Modified (Vehicle restoration)
« on: February 22, 2017, 08:20:55 PM »
Oooh, this is cool
Sorry about not replying earlier, you can modify my cars however you want
Sorry about not replying earlier, you can modify my cars however you want
3
Suggestions & Requests / Re: "Plank" vehicle
« on: December 20, 2016, 01:25:28 PM »One issue I had when there wasn't any wheels on my car [on accident], was the fact that it would slide around everywhere.Isn't there a friction variable in the vehicle datablock?
I didn't know how to resolve the sliding part without putting in the correct wheel datablocks.
Point being is that I can't see this possible, unless someone besides me knows their Blockland physics.
4
Add-Ons / Re: [Brick] Plate high ramps v1.1 - now with halfbrick high ramps! Also prints
« on: December 07, 2016, 01:08:24 PM »these have culling errors, when my viewpoint is below them the tops vanishI just checked and haven't noticed anything like that, screenshots would be helpful
at least on the print ones
So are you back to making addons or was this just a spur of the moment?I'll stick around for a bit
5
Suggestions & Requests / Re: Body armor addons?
« on: November 26, 2016, 04:50:54 AM »
I can try making some, just provide pictures of what you want
6
Add-Ons / Re: [Brick] Plate high ramps v1.1 - now with halfbrick high ramps! Also prints
« on: November 20, 2016, 06:14:19 PM »
Updated the pack with halfbrick high ramps, there's also a separate print pack.
also where were you all this time turtJust wanted to take a break for awhile, so I left quietly. Did forget all during that year though :\
its been like
a year
forget my suggestionAlready happened
7
Creativity / Re: I decided to forget with a piano
« on: November 19, 2016, 02:03:42 PM »what?"I decided to forget with a piano"
8
Add-Ons / Re: [Brick] Plate high ramps
« on: November 19, 2016, 05:34:10 AM »
It's up on blockland glass, updated the dl link in the OP
Working on print versions, currently they use default 1x1, 1x2 and 2x2 prints, everything bigger than that tiles
How about a 45 degree ramp?I'll make a half-brick version, it'll be ~40°
could you make a pack of these but inverted?
Later, sure, maybe even corners.
omg welcome back!Hi, nice to see you're still around
Working on print versions, currently they use default 1x1, 1x2 and 2x2 prints, everything bigger than that tiles
9
Add-Ons / Re: [Brick] Plate high ramps
« on: November 18, 2016, 12:35:52 PM »
I'm glad you're liking the pack :)
Welcome back my friend.Hey, good to see you again!
you should put this on blockland glassUploaded, will post a link to OP once it's approved
Could you also potentially make print versions? I would love to do completely smooth and also brick side prints on them.Print versions should be easy to do, though I don't think side prints would work as it would require different prints for each of the 30 bricks or they'll stretch, I'll just do a tiling print texture. However, I can make a separate pack with side textures applied instead of the studs like tile plates, if you need them.
can you add a version with no textures?I'll make prints versions onto which you can apply blank prints
can you ad some inverted ones too?Later, sure, maybe even corners.
x5 and x7 ramps being added would be nice but i'll have to actually try to use the bricks first to see if i'll need themI didn't add 5 and 7 because their angle is pretty much the same as the adjacent x4, x6 and x8 ramps, if you do require them do tell
Can you add more, like 45 degree ramps? i need them with studs on em'Like, half bricks tall ones? Shouldn't be hard
Do vehicles still glitch through them though?With these you're driving on an angled flat surface instead of stairs, so you should glitch way less.
10
Suggestions & Requests / Re: Slate Ramps
« on: November 16, 2016, 02:18:34 PM »
Released my pack here
11
Add-Ons / [Brick] Plate high ramps v1.1 - now with halfbrick high ramps! Also prints
« on: November 16, 2016, 02:13:18 PM »Plate high ramps
A pack of ramps with plate height, very useful for making slanted roads for vehicles.
Version 1.1: Now with halfbrick high ramps!
+
DOWNLOAD
mediafire mirror
Plate high print ramps
Same bricks, except the top texture is replaced with prints. Uses default 1x1f, 1x2f and 2x2f prints.
+
DOWNLOAD
mediafire mirror
A pack of ramps with plate height, very useful for making slanted roads for vehicles.
Version 1.1: Now with halfbrick high ramps!
+
DOWNLOAD
mediafire mirror
Plate high print ramps
Same bricks, except the top texture is replaced with prints. Uses default 1x1f, 1x2f and 2x2f prints.
+
DOWNLOAD
mediafire mirror
14
Modification Help / Re: TheTurtorn's vehicle topic - p24
« on: August 01, 2015, 05:36:31 PM »
Quickly changed the handling for drag variant, not exactly what I wanted from it in the start, but, blockland's physics are a pain when you want to create something complex, and everything is better than letting the bullrout rot on my HDD until eventual loss
Download
I didn't (and still don't) feel like doing anything related to blockland and so went to do other stuff, made high-poly models, coded with Unity a bit, etc. Pretty sure I won't release anything here in the future, but you never know.
Download
I didn't (and still don't) feel like doing anything related to blockland and so went to do other stuff, made high-poly models, coded with Unity a bit, etc. Pretty sure I won't release anything here in the future, but you never know.
15