Blockland .BLB Conversions

[Altiris]

Alright so I am trying to find out the Y coordinates for 45, 72, and 80 degree ramps as if they were blocks.
If there is, I also want to know the formula to translate degrees to a size coordinate.


Thanks everyone, I need this ASAP.

[Ad Bot]

[jes00]

You want to change those ramps into blocks?

[Altiris]

You want to change those ramps into blocks?

Well sort of, I asked you this before, I originally asked you what the Y Coordiantes for 25 degrees ramps are and you told me

1.5
-0.833
-0.833
1.5

Then I asked you what the Y coordinate would be if the ramp were a brick and you wrote

1.5
1.5
1.5
1.5

I am asking how you got that and/or what the Y coordinates would be if the 25, 45, 72 and 80 degrees were bricks.
So in turn yes I technically want to turn Ramps into Bricks but not physically, I just want to do this so I can get their Y coordinate.

[jes00]

So in turn yes I technically want to turn Ramps into Bricks but not physically, I just want to do this so I can get their Y coordinate.

I don't understand this but.

Look for the face with the RAMP texture and on the Y scale take the lower numbers and make them into the higher numbers and than it will be an in than the brick will no longer be a ramp.

[Altiris]

I don't understand this but.

Look for the face with the RAMP texture and on the Y scale take the lower numbers and make them into the higher numbers and than it will be an in than the brick will no longer be a ramp.

Im sorry but after "higher numbers" I can't read the rest, you accidentaly said the samething. I just want to know how you went from

1.5
-0.833
-0.833
1.5


to

1.5
1.5
1.5
1.5

Thats all ive been asking this whole time.

[jes00]

1.5
-0.833
-0.833
1.5


to

1.5
1.5
1.5
1.5

Thats all ive been asking this whole time.

Oh lol.

Each line is a corner of the RAMP face and since the middle two are lower numbers the face will be sloping down. But if you make all the numbers the same the face will be flat.

[Altiris]

Oh lol.

Each line is a corner of the RAMP face and since the middle two are lower numbers the face will be sloping down. But if you make all the numbers the same the face will be flat.

Okay so, I opened up the 1x2 Ramp.BLB and noticed there are a bunch of TEX:    there are Sides, BottomEdges, Top etc. Is RAMP the only one that I need?


In this image I see 1.5, -0.833, -0.833, 1.5. You said not to worry about -0.833 because they are in the middle.



I opened up a 2x2 ramp and see 7.5, -6.833, -6.833, 7.5. Once again, 7.5 is all that matters then correct?

[jes00]

Okay so, I opened up the 1x2 Ramp.BLB and noticed there are a bunch of TEX:    there are Sides, BottomEdges, Top etc. Is RAMP the only one that I need?


In this image I see 1.5, -0.833, -0.833, 1.5. You said not to worry about -0.833 because they are in the middle.



I opened up a 2x2 ramp and see 7.5, -6.833, -6.833, 7.5. Once again, 7.5 is all that matters then correct?

You want to change the -0.833 to 1.5 and in the second one change -6.833 to 7.5

[Altiris]

You want to change the -0.833 to 1.5 and in the second one change -6.833 to 7.5

Alright thanks dude!