Author Topic: Running a spark through screws. (Read 3832 times)

Sirrus · February 13, 2009, 07:28:31 PM

I'm trying to build a detached sparking mechanism for a potato gun, and I was wondering how close I would have to put two screws to allow a spark to pass through, attached at the other end to a lightswitch and a battery.

Ad Bot · Advertisement

vv45689 · February 13, 2009, 07:38:06 PM

stick`em in opposit ends if it blows up look on the bright side you have mashed potatoes

Sirrus · February 13, 2009, 07:38:42 PM

Serious answer please.

Dropshock · February 13, 2009, 07:39:12 PM

Quote from: vv45689 on February 13, 2009, 07:38:06 PM

stick`em in opposit ends if it blows up look on the bright side you have mashed potatoes

was that supposed to be funny?
get the forget out.

FrAgGEr · February 13, 2009, 07:39:31 PM

Quote from: vv45689 on February 13, 2009, 07:38:06 PM

stick`em in opposit ends if it blows up look on the bright side you have mashed potatoes

i actually laughed.

WRB852 · February 13, 2009, 07:46:05 PM

Get a grill lighter, those work well. Or just a stick lighter might work.

Sirrus · February 13, 2009, 08:01:32 PM

Quote from: WRB852 on February 13, 2009, 07:46:05 PM

Get a grill lighter, those work well. Or just a stick lighter might work.

That's what I have in my current one; I need to make a detached sparker to test some more volatile accelerants like propane; I don't want to take my hand off if the back blows out.

Rughugger · February 13, 2009, 08:01:46 PM

Depends on the voltage really, but 3/4 of an inch should be enough for a spark to jump.

ryanb31394 · February 13, 2009, 08:07:50 PM

Quote from: Rughugger on February 13, 2009, 08:01:46 PM

Depends on the voltage really, but 3/4 of an inch should be enough for a spark to jump.

QFT, the higher the voltage the further the arc is able to travel.

fat boy · February 13, 2009, 08:10:27 PM

depending on your fuel I would say that I good spark with 12 volts would be at about 1mm to 1.5mm apart

(IN OPEN AIR).

Jsk2003 · February 13, 2009, 08:30:35 PM

Keep zapping and push screw closer and closer until it finally travels through the air.

TapeDeck · February 13, 2009, 09:16:34 PM

Quote from: Rughugger on February 13, 2009, 08:01:46 PM

Depends on the ~~voltage~~ really, but 3/4 of an inch should be enough for a spark to jump.

Quote from: ryanb31394 on February 13, 2009, 08:07:50 PM

QFT, the higher the ~~voltage~~ the further the arc is able to travel.

I believe they are called Amps.

Also, what is your power source?

Sirrus · February 13, 2009, 09:18:34 PM

Quote from: TapeDeck on February 13, 2009, 09:16:34 PM

]I believe they are called Amps.

Also, what is your power source?

Battery. Toggled with a regular old light switch.

TapeDeck · February 13, 2009, 09:19:56 PM

Quote from: Sirrus on February 13, 2009, 09:18:34 PM

Battery. Toggled with a regular old light switch.

I know, what kind? AAA or car battery?

They are different, you know.

Sirrus · February 13, 2009, 09:24:21 PM

Quote from: TapeDeck on February 13, 2009, 09:19:56 PM

I know, what kind? AAA or car battery?

They are different, you know.

Probably an 9 volt.